一种抗运动干扰的实时心率提取方法

针对基于容积脉搏波（PPG）提取运动心率时，传统心率提取算法由于运动噪声干扰使测量结果误差大、实时性不好的问题，提出一种抗运动干扰的实时心率提取方法。该方法通过实时小波去噪，同时结合三轴加速度信号（ACC）对运动进行分类训练，计算各运动状态心率增益，对实时心率值进行补偿。实验结果表明，通过与同时采集的ECG信号计算出的实时心率进行对比，绝对误差率仅为1.2%左右。相比传统心率提取算法，该算法具有抗干扰性强，实时准确的特点。     

铜基化合物的可见光催化研究进展

与传统贵金属光催化剂相比，铜基光催化剂具有价格低廉、绿色环保、反应条件温和、光催化活性可调节等优势，受到合成化学家们广泛关注。本文简述了铜基催化剂的光催化历史，回顾了近五年来铜基化合物在可见光催化领域的研究成果与进展，总结了铜基催化剂的独立光催化机理与协同光催化机理；简要阐述了铜催化剂在不同类型反应中的应用，重点讨论了铜(Ⅰ)催化剂在烯烃官能化、碳-碳偶联、碳-杂偶联、原位催化等反应中的应用研究，表明铜基化合物在光催化合成领域具有很大的应用潜力。对未来的研究工作进行了展望，指出拓展催化剂的反应适用性、探索催化剂的氧化还原能力、进一步开发催化剂在手性合成中的应用将是该领域的研究重点。     

SNCR脱硝技术在液态排渣煤粉工业锅炉中的应用

为了检验选择性非催化还原（SNCR）脱硝技术在高效低NO_x液态排渣煤粉工业锅炉中的应用效果，本文在一台8.4MW有机热载体锅炉炉膛内开展了SNCR脱硝技术工业化试验研究。选用尿素作为还原剂，搭建了工业化SNCR脱硝试验平台。在10%、15%、20%三种浓度尿素溶液下进行了不同尿素溶液喷射量、不同氧含量、不同锅炉负荷下的SNCR脱硝试验研究。试验结果表明，提出的“低NO_x燃烧+SNCR脱硝”耦合技术方案是可行的，SNCR脱硝效率在80%以上，完全能够达到烟气中NO_x低于50mg/m³的超低排放要求。     

Investigation of the energy-size reduction and mineral liberation of raw coal in the Hardgrove mill

Raw coal was ground in a Hardgrove mill, and mineral liberation from coal was investigated by float-sink test and electron probe microanalyzer (EPMA). Based on EPMA, associated conditions of mineral were determined. Analyses of energy-size reduction show that energy efficiency decreases with time. For +0.074 mm progenies, yields of particles in ?1.5 g.cm^?3 decrease with the increase of size and time, and products in +1.8 g.cm^?3 show the opposite trend. EPMA of 0.25–0.125 mm, 1.5–1.8 g.cm^?3 products ground for 10 min indicates that only part of minerals are liberated. For ?0.074 mm products, the yield of particles in ?1.5 g.cm^?3 decreases by 23.36% in last several minutes, but ash content of +1.8 g.cm^?3 also decreases by 13.18%. Since breakage of raw coal in last 9 min does not reduce particle size obviously, and liberation degree cannot be improved dramatically, closed grinding of 10 min in Hardgrove mill is proper to balance the size reduction and mineral liberation.     

不同降雨入渗条件下预应力锚索加固边坡稳定性分析

为了研究不同降雨条件下边坡安全系数及预应力锚索轴力变化规律,以省道S303沿线某边坡为研究对象,考虑土体饱和-非饱和渗流与非饱和强度理论,基于有限元分析,对不同降雨工况下的孔隙水压分布、锚索轴力及采用强度折减法计算的边坡安全系数变化规律进行了研究。结果表明: 降雨量一定时,降雨入渗范围随雨强增大而减小,暂态饱和区域随雨强增加而增大; 边坡在加固前后的安全系数均随降雨量增加而不断减小,采用预应力锚索加固能有效提高边坡安全系数,并减小降雨对边坡稳定性的影响; 随着降雨量增加,各锚索轴力均增大,当降雨量一定时,雨强越小,对应的锚索轴力提升幅度越大,靠近底部的锚索轴力对降雨最为敏感。     

基于EVSEWT的下击暴流时变平均风提取

下击暴流等极端风具有强烈的非平稳特性，给风场特性分析、结构响应计算带来挑战。根据经验将非平稳风分为时变平均风和零均值脉动风分别进行分析，是处理非平稳风速信号的有效方法。分析了几种常见时变均值提取方法的优缺点，在此基础上提出一种基于能量波谷寻找的经验小波变换方法，用于下击暴流时变平均风速提取，并将提取的时变平均风和脉动风用于分析某幢高层建筑顶部位移响应。对2组下击暴流的分析结果得出：与经验模态分解和离散小波变换方法相比，基于能量波谷寻找的经验小波变换方法模型提取的时变平均风更符合预期，对应的结构响应偏于安全。     

Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

高频氢等离子体增强还原制备超细铜粉

利用高频感应热氢等离子体强化还原制备超细铜粉，考察了加料速率、还原氢气流量、氢气分布位置、反应区空间、冷却温度等因素对铜粉颗粒性能的影响，对制备的铜粉颗粒进行氧含量、XRD晶体结构、松装密度、粒度分布和比表面积的表征。结果表明，优化的工艺条件为反应区内径100 mm，加料速率4 g/min，淬火气氩气气量500 L/h，氢气气量500 L/h并通入少量载气，由氢等离子电离产生的氢自由基可强化反应实现瞬时还原，不仅可控制铜粉形貌，还能有效控制铜粉颗粒大小；利用该方法制备出粒径分布100?200 nm、分散性好的超细球形铜粉颗粒。该方法操作简便、产品纯度高、气氛可控、对环境污染小。     

Deposition of nanostructured LSM perovskite thin film on dense YSZ substrate by airbrushed solution combustion (ASC) for application in SOFC cathodes

To make SOFC high efficiency energy generation devices, thin ceramic films are proposed as their main components. The rate of the oxygen reduction reaction is relevant for the overall performance of the SOFC, hence a lot of attention is given to the cathodes and their interfaces. The airbrushed solution combustion (ASC) method was used to fabricate an LSM thin film on a dense YSZ substrate. A single phase LSM perovskite was obtained with very thin and interconnected porosity, and a small average grain size (55 nm). The nanostructured LSM thin film electrode showed a low total activation energy (1.27 eV) at high temperatures, but a high area specific resistance at 850°C (55 Ω.cm²). The activation energy for the dissociative adsorption and diffusion of oxygen was significantly low (1.27 eV), while the charge transfer and oxygen ion migration activation energy at the LSM/YSZ interface (1.28 eV) was closer to those usually reported.